모두의 코드
SMSW (Intel x86/64 assembly instruction)

작성일 : 2020-09-01 이 글은 777 번 읽혔습니다.

SMSW

Store Machine Status Word

참고 사항

아래 표를 해석하는 방법은 x86-64 명령어 레퍼런스 읽는 법 글을 참조하시기 바랍니다.

Opcode*

Instruction

Op/
En

64-Bit
Mode

Compat/
Leg Mode

Description

0F 01 /4

SMSW r/m16

M

Valid

Valid

Store machine status word to r/m16.

0F 01 /4

SMSW r32/m16

M

Valid

Valid

Store machine status word in low-order 16 bits of r32/m16; high-order 16 bits of r32 are undefined.

REX.W + 0F 01 /4

SMSW r64/m16

M

Valid

Valid

Store machine status word in low-order 16 bits of r64/m16; high-order 16 bits of r32 are undefined.

Instruction Operand Encoding

Op/En

Operand 1

Operand 2

Operand 3

Operand 4

M

ModRM:r/m (w)

NA

NA

NA

Description

Stores the machine status word (bits 0 through 15 of control register CR0) into the destination operand. The desti-nation operand can be a general-purpose register or a memory location.

In non-64-bit modes, when the destination operand is a 32-bit register, the low-order 16 bits of register CR0 are copied into the low-order 16 bits of the register and the high-order 16 bits are undefined. When the destination operand is a memory location, the low-order 16 bits of register CR0 are written to memory as a 16-bit quantity, regardless of the operand size.

In 64-bit mode, the behavior of the SMSW instruction is defined by the following examples:

  • SMSW r16 operand size 16, store CR0[15:0] in r16

  • SMSW r32 operand size 32, zero-extend CR0[31:0], and store in r32

  • SMSW r64 operand size 64, zero-extend CR0[63:0], and store in r64

  • SMSW m16 operand size 16, store CR0[15:0] in m16

  • SMSW m16 operand size 32, store CR0[15:0] in m16 (not m32)

  • SMSW m16 operands size 64, store CR0[15:0] in m16 (not m64)

SMSW is only useful in operating-system software. However, it is not a privileged instruction and can be used in application programs if CR4.UMIP = 0. It is provided for compatibility with the Intel 286 processor. Programs and procedures intended to run on IA-32 and Intel 64 processors beginning with the Intel386 processors should use the MOV CR instruction to load the machine status word.

See "Changes to Instruction Behavior in VMX Non-Root Operation" in Chapter 25 of the Intel(R) 64 and IA-32 Archi-tectures Software Developer's Manual, Volume 3C, for more information about the behavior of this instruction in VMX non-root operation.

Operation

DEST <- CR0[15:0]; 
(* Machine status word *)

Flags Affected

None.

Protected Mode Exceptions

#GP(0)

  • If the destination is located in a non-writable segment.

  • If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

  • If the DS, ES, FS, or GS register is used to access memory and it contains a NULL segment selector.

  • If CR4.UMIP = 1 and CPL > 0.

#SS(0)

  • If a memory operand effective address is outside the SS segment limit.

#PF(fault-code)

  • If a page fault occurs.

#AC(0)

  • If alignment checking is enabled and an unaligned memory reference is made while CPL = 3.

#UD

  • If the LOCK prefix is used.

Real-Address Mode Exceptions

#GP

  • If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

#SS(0)

  • If a memory operand effective address is outside the SS segment limit.

#UD

  • If the LOCK prefix is used.

Virtual-8086 Mode Exceptions

#GP(0)

  • If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

  • If CR4.UMIP = 1.

#SS(0)

  • If a memory operand effective address is outside the SS segment limit.

#PF(fault-code)

  • If a page fault occurs.

#AC(0)

  • If alignment checking is enabled and an unaligned memory reference is made.

#UD

  • If the LOCK prefix is used.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

#SS(0)

  • If a memory address referencing the SS segment is in a non-canonical form.

#GP(0)

  • If the memory address is in a non-canonical form.

  • If CR4.UMIP = 1 and CPL > 0.

#PF(fault-code)

  • If a page fault occurs.

#AC(0)

  • If alignment checking is enabled and an unaligned memory reference is made while CPL = 3.

#UD

  • If the LOCK prefix is used.

첫 댓글을 달아주세요!
프로필 사진 없음
강좌에 관련 없이 궁금한 내용은 여기를 사용해주세요

    댓글을 불러오는 중입니다..