##
모두의 코드

FCOS (Intel x86/64 assembly instruction)

## FCOS

Cosine

참고 사항

아래 표를 해석하는 방법은 x86-64 명령어 레퍼런스 읽는 법 글을 참조하시기 바랍니다.

Opcode | Instruction | 64-Bit | Compat/ | Description |
---|---|---|---|---|

D9 FF | Valid | Valid | Replace ST(0) with its approximate cosine. |

### Description

Computes the approximate cosine of the source operand in register ST(0) and stores the result in ST(0). The source operand must be given in radians and must be within the range -2^{63} to +2^{63} . The following table shows the results obtained when taking the cosine of various classes of numbers.

### Table 3-23. FCOS Results

ST(0) SRC | ST(0) DEST |
---|---|

- $\infty$ | * |

- F | -1 to +1 |

- 0 | + 1 |

+ 0 | + 1 |

+ F | - 1 to + 1 |

+ $\infty$ | * |

NaN | NaN |

### NOTES:

F Means finite floating-point value.

* Indicates floating-point invalid-arithmetic-operand (#IA) exception.

If the source operand is outside the acceptable range, the C2 flag in the FPU status word is set, and the value in register ST(0) remains unchanged. The instruction does not raise an exception when the source operand is out of range. It is up to the program to check the C2 flag for out-of-range conditions. Source values outside the range -2^{63} to +2^{63} can be reduced to the range of the instruction by subtracting an appropriate integer multiple of 2. However, even within the range -2^{63} to +2^{63} , inaccurate results can occur because the finite approximation of used internally for argument reduction is not sufficient in all cases. Therefore, for accurate results it is safe to apply FCOS only to arguments reduced accurately in software, to a value smaller in absolute value than 3/8. See the sections titled "Approximation of Pi" and "Transcendental Instruction Accuracy" in Chapter 8 of the Intel(R) 64 and IA-32 Architectures Software Developer's Manual, Volume 1, for a discussion of the proper value to use for in performing such reductions.

This instruction's operation is the same in non-64-bit modes and 64-bit mode.

### Operation

IF |ST(0)| < 2\footnote{63} THEN C2 <- 0; ST(0) <- FCOS(ST(0)); // approximation of cosine ELSE (* Source operand is out-of-range *) C2 <- 1; FI;

### FPU Flags Affected

C1 Set to 0 if stack underflow occurred.

Set if result was rounded up; cleared otherwise.

Undefined if C2 is 1.

C2 Set to 1 if outside range (-2^{63} < source operand < +2^{63} ); otherwise, set to 0.

C0, C3 Undefined.

### Floating-Point Exceptions

#IS Stack underflow occurred.

#IA Source operand is an SNaN value, $\infty$, or unsupported format.

#D Source is a denormal value.

#P Value cannot be represented exactly in destination format.

### Protected Mode Exceptions

#### #NM

CR0.EM[bit 2] or CR0.TS[bit 3] = 1.

#### #MF

If there is a pending x87 FPU exception.

#### #UD

If the LOCK prefix is used.

### Real-Address Mode Exceptions

Same exceptions as in protected mode.

### Virtual-8086 Mode Exceptions

Same exceptions as in protected mode.

### Compatibility Mode Exceptions

Same exceptions as in protected mode.

### 64-Bit Mode Exceptions

Same exceptions as in protected mode.

댓글을 불러오는 중입니다..