모두의 코드
FUCOM, FUCOMP, FUCOMPPs (Intel x86/64 assembly instruction)

작성일 : 2020-09-01 이 글은 598 번 읽혔습니다.

FUCOM, FUCOMP, FUCOMPP

Unordered Compare Floating Point Values

참고 사항

아래 표를 해석하는 방법은 x86-64 명령어 레퍼런스 읽는 법 글을 참조하시기 바랍니다.

Opcode

Instruction

64-Bit
Mode

Compat/
Leg Mode

Description

DD E0+i

FUCOM ST(i)

Valid

Valid

Compare ST(0) with ST(i).

DD E1

FUCOM

Valid

Valid

Compare ST(0) with ST(1).

DD E8+i

FUCOMP ST(i)

Valid

Valid

Compare ST(0) with ST(i) and pop register stack.

DD E9

FUCOMP

Valid

Valid

Compare ST(0) with ST(1) and pop register stack.

DA E9

FUCOMPP

Valid

Valid

Compare ST(0) with ST(1) and pop register stack twice.

Description

Performs an unordered comparison of the contents of register ST(0) and ST(i) and sets condition code flags C0, C2, and C3 in the FPU status word according to the results (see the table below). If no operand is specified, the contents of registers ST(0) and ST(1) are compared. The sign of zero is ignored, so that -0.0 is equal to +0.0.

Table 3-41. FUCOM/FUCOMP/FUCOMPP Results

Comparison Results*

C3

C2

C0

ST0 > ST(i)

0

0

0

ST0 < ST(i)

0

0

1

ST0 = ST(i)

1

0

0

Unordered

1

1

1

NOTES:

* Flags not set if unmasked invalid-arithmetic-operand (#IA) exception is generated.

An unordered comparison checks the class of the numbers being compared (see "FXAM--Examine Floating-Point" in this chapter). The FUCOM/FUCOMP/FUCOMPP instructions perform the same operations as the FCOM/FCOMP/FCOMPP instructions. The only difference is that the FUCOM/FUCOMP/FUCOMPP instructions raise the invalid-arithmetic-operand exception (#IA) only when either or both operands are an SNaN or are in an unsup-ported format; QNaNs cause the condition code flags to be set to unordered, but do not cause an exception to be generated. The FCOM/FCOMP/FCOMPP instructions raise an invalid-operation exception when either or both of the operands are a NaN value of any kind or are in an unsupported format.

As with the FCOM/FCOMP/FCOMPP instructions, if the operation results in an invalid-arithmetic-operand exception being raised, the condition code flags are set only if the exception is masked.

The FUCOMP instruction pops the register stack following the comparison operation and the FUCOMPP instruction pops the register stack twice following the comparison operation. To pop the register stack, the processor marks the ST(0) register as empty and increments the stack pointer (TOP) by 1.

This instruction's operation is the same in non-64-bit modes and 64-bit mode.

Operation

CASE (relation of operands) OF
    ST > SRC: C3, C2, C0 <- 000;
    ST < SRC: C3, C2, C0 <- 001;
    ST = SRC: C3, C2, C0 <- 100;
ESAC;
IF ST(0) or SRC = QNaN, but not SNaN or unsupported format
    THEN 
          C3, C2, C0 <- 111;
    ELSE (* ST(0) or SRC is SNaN or unsupported format *)
           #IA;
          IF FPUControlWord.IM = 1
                THEN 
                      C3, C2, C0 <- 111;
          FI;
FI;
IF Instruction = FUCOMP 
    THEN 
          PopRegisterStack;
FI;
IF Instruction = FUCOMPP 
    THEN 
          PopRegisterStack; 
FI;

FPU Flags Affected

C1 Set to 0 if stack underflow occurred.

C0, C2, C3 See Table 3-41.

Floating-Point Exceptions

#IS Stack underflow occurred.

#IA One or both operands are SNaN values or have unsupported formats. Detection of a QNaN value in and of itself does not raise an invalid-operand exception.

#D One or both operands are denormal values.

Protected Mode Exceptions

#NM

  • CR0.EM[bit 2] or CR0.TS[bit 3] = 1.

#MF

  • If there is a pending x87 FPU exception.

#UD

  • If the LOCK prefix is used.

Real-Address Mode Exceptions

Same exceptions as in protected mode.

Virtual-8086 Mode Exceptions

Same exceptions as in protected mode.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

Same exceptions as in protected mode.

첫 댓글을 달아주세요!
프로필 사진 없음
강좌에 관련 없이 궁금한 내용은 여기를 사용해주세요

    댓글을 불러오는 중입니다..