LOOP, LOOPcc

Loop According to ECX Counter

참고 사항

Instruction Operand Encoding

Description

Performs a loop operation using the RCX, ECX or CX register as a counter (depending on whether address size is 64 bits, 32 bits, or 16 bits). Note that the LOOP instruction ignores REX.W; but 64-bit address size can be over-ridden using a 67H prefix.

Each time the LOOP instruction is executed, the count register is decremented, then checked for 0. If the count is 0, the loop is terminated and program execution continues with the instruction following the LOOP instruction. If the count is not zero, a near jump is performed to the destination (target) operand, which is presumably the instruction at the beginning of the loop.

The target instruction is specified with a relative offset (a signed offset relative to the current value of the instruc-tion pointer in the IP/EIP/RIP register). This offset is generally specified as a label in assembly code, but at the machine code level, it is encoded as a signed, 8-bit immediate value, which is added to the instruction pointer. Offsets of -128 to +127 are allowed with this instruction.

Some forms of the loop instruction (LOOPcc) also accept the ZF flag as a condition for terminating the loop before the count reaches zero. With these forms of the instruction, a condition code (cc) is associated with each instruction to indicate the condition being tested for. Here, the LOOPcc instruction itself does not affect the state of the ZF flag; the ZF flag is changed by other instructions in the loop.

Operation

IF (AddressSize = 32)THEN Count is ECX;ELSE IF (AddressSize = 64)Count is RCX;
ELSE Count is CX; 
FI;
Count <- Count - 1;
IF Instruction is not LOOP
    THEN
          IF (Instruction <- LOOPE) or (Instruction <- LOOPZ)
                THEN IF (ZF = 1) and (Count != 0)
                            THEN BranchCond <- 1;
                            ELSE BranchCond <- 0;
                      FI;
                ELSE (Instruction = LOOPNE) or (Instruction = LOOPNZ)
                      IF (ZF = 0 ) and (Count != 0)
                            THEN BranchCond <- 1;
                            ELSE BranchCond <- 0;
FI;
          FI;
    ELSE (* Instruction = LOOP *)
          IF (Count != 0)
                THEN BranchCond <- 1;
                ELSE BranchCond <- 0;
          FI;
FI;
IF BranchCond = 1
    THEN
          IF OperandSize = 32
                THEN EIP <- EIP + SignExtend(DEST);
                ELSE IF OperandSize = 64
                      THEN RIP <- RIP + SignExtend(DEST);
                      FI;
                ELSE IF OperandSize = 16
                      THEN EIP <- EIP AND 0000FFFFH;
                      FI;
          FI;
          IF OperandSize = (32 or 64)
                THEN IF (R/E)IP < CS.Base or (R/E)IP > CS.Limit
                      #GP; FI;
                      FI;
          FI;
    ELSE
          Terminate loop and continue program execution at (R/E)IP;
FI;

Flags Affected

None

Protected Mode Exceptions

#GP(0)

• If the offset being jumped to is beyond the limits of the CS segment.

#UD

• If the LOCK prefix is used.

Real-Address Mode Exceptions

#GP

• If the offset being jumped to is beyond the limits of the CS segment or is outside of the effec-tive address space from 0 to FFFFH. This condition can occur if a 32-bit address size override prefix is used.

#UD

• If the LOCK prefix is used.

Virtual-8086 Mode Exceptions

Same exceptions as in real address mode.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

#GP(0)

• If the offset being jumped to is in a non-canonical form.

#UD

• If the LOCK prefix is used.

첫 댓글을 달아주세요!

강좌에 관련 없이 궁금한 내용은 여기를 사용해주세요

다음으로 로그인

또는 직접 입력하세요 (댓글 수정시 비밀번호가 필요합니다)

댓글 달기

댓글을 불러오는 중입니다..