VERR, VERW

Verify a Segment for Reading or Writing

참고 사항

Instruction Operand Encoding

Description

Verifies whether the code or data segment specified with the source operand is readable (VERR) or writable (VERW) from the current privilege level (CPL). The source operand is a 16-bit register or a memory location that contains the segment selector for the segment to be verified. If the segment is accessible and readable (VERR) or writable (VERW), the ZF flag is set; otherwise, the ZF flag is cleared. Code segments are never verified as writable. This check cannot be performed on system segments.

To set the ZF flag, the following conditions must be met:

• The segment selector is not NULL.

• The selector must denote a descriptor within the bounds of the descriptor table (GDT or LDT).

• The selector must denote the descriptor of a code or data segment (not that of a system segment or gate).

• For the VERR instruction, the segment must be readable.

• For the VERW instruction, the segment must be a writable data segment.

• If the segment is not a conforming code segment, the segment's DPL must be greater than or equal to (have less or the same privilege as) both the CPL and the segment selector's RPL.

The validation performed is the same as is performed when a segment selector is loaded into the DS, ES, FS, or GS register, and the indicated access (read or write) is performed. The segment selector's value cannot result in a protection exception, enabling the software to anticipate possible segment access problems.

This instruction's operation is the same in non-64-bit modes and 64-bit mode. The operand size is fixed at 16 bits.

Operation

IF SRC(Offset) > (GDTR(Limit) or (LDTR(Limit))
    THEN ZF <- 0; FI;
Read segment descriptor;
IF SegmentDescriptor(DescriptorType) = 0 (* System segment *)
or (SegmentDescriptor(Type) != conforming code segment) 
and (CPL > DPL) or (RPL > DPL)
    THEN
          ZF <- 0;
    ELSE
          IF ((Instruction = VERR) and (Segment readable))
          or ((Instruction = VERW) and (Segment writable))
                THEN 
                      ZF <- 1;
          FI;
FI;

Flags Affected

The ZF flag is set to 1 if the segment is accessible and readable (VERR) or writable (VERW); otherwise, it is set to 0.

Protected Mode Exceptions

#GP(0)

• If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

• If the DS, ES, FS, or GS register is used to access memory and it contains a NULL segment selector.

#SS(0)

• If a memory operand effective address is outside the SS segment limit.

#PF(fault-code)

• If a page fault occurs.

#AC(0)

• If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.

#UD

• If the LOCK prefix is used.

Real-Address Mode Exceptions

#UD

• The VERR and VERW instructions are not recognized in real-address mode.

• If the LOCK prefix is used.

Virtual-8086 Mode Exceptions

#UD

• The VERR and VERW instructions are not recognized in virtual-8086 mode.

• If the LOCK prefix is used.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

#SS(0)

• If a memory address referencing the SS segment is in a non-canonical form.

#GP(0)

• If the memory address is in a non-canonical form.

#PF(fault-code)

• If a page fault occurs.

#AC(0)

• If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.

#UD

• If the LOCK prefix is used.

첫 댓글을 달아주세요!

강좌에 관련 없이 궁금한 내용은 여기를 사용해주세요

다음으로 로그인

또는 직접 입력하세요 (댓글 수정시 비밀번호가 필요합니다)

댓글 달기

댓글을 불러오는 중입니다..