모두의 코드
RDTSCP (Intel x86/64 assembly instruction)

작성일 : 2020-09-01 이 글은 1503 번 읽혔습니다.

RDTSCP

Read Time-Stamp Counter and Processor ID

참고 사항

아래 표를 해석하는 방법은 x86-64 명령어 레퍼런스 읽는 법 글을 참조하시기 바랍니다.

Opcode*

Instruction

Op/
En

64-Bit
Mode

Compat/
Leg Mode

Description

0F 01 F9

RDTSCP

NP

Valid

Valid

Read 64-bit time-stamp counter and IA32_TSC_AUX value into EDX:EAX and ECX.

Instruction Operand Encoding

Op/En

Operand 1

Operand 2

Operand 3

Operand 4

NP

NA

NA

NA

NA

Description

Reads the current value of the processor's time-stamp counter (a 64-bit MSR) into the EDX:EAX registers and also reads the value of the IA32TSCAUX MSR (address C0000103H) into the ECX register. The EDX register is loaded with the high-order 32 bits of the IA32TSC MSR; the EAX register is loaded with the low-order 32 bits of the IA32TSC MSR; and the ECX register is loaded with the low-order 32-bits of IA32TSCAUX MSR. On processors that support the Intel 64 architecture, the high-order 32 bits of each of RAX, RDX, and RCX are cleared.

The processor monotonically increments the time-stamp counter MSR every clock cycle and resets it to 0 whenever the processor is reset. See "Time Stamp Counter" in Chapter 17 of the Intel(R) 64 and IA-32 Architectures Software Developer's Manual, Volume 3B, for specific details of the time stamp counter behavior.

The time stamp disable (TSD) flag in register CR4 restricts the use of the RDTSCP instruction as follows. When the flag is clear, the RDTSCP instruction can be executed at any privilege level; when the flag is set, the instruction can only be executed at privilege level 0.

The RDTSCP instruction waits until all previous instructions have been executed before reading the counter. However, subsequent instructions may begin execution before the read operation is performed.

See "Changes to Instruction Behavior in VMX Non-Root Operation" in Chapter 25 of the Intel(R) 64 and IA-32 Archi-tectures Software Developer's Manual, Volume 3C, for more information about the behavior of this instruction in VMX non-root operation.

Operation

IF (CR4.TSD = 0) or (CPL = 0) or (CR0.PE = 0) 
    THEN 
          EDX:EAX <- TimeStampCounter;
          ECX <- IA32_TSC_AUX[31:0];
    ELSE (* CR4.TSD = 1 and (CPL = 1, 2, or 3) and CR0.PE = 1 *)
          #GP(0);
FI;

Flags Affected

None.

Protected Mode Exceptions

#GP(0)

  • If the TSD flag in register CR4 is set and the CPL is greater than 0.

#UD

  • If the LOCK prefix is used.

  • If CPUID.80000001H:EDX.RDTSCP[bit 27] = 0.

Real-Address Mode Exceptions

#UD

  • If the LOCK prefix is used.

  • If CPUID.80000001H:EDX.RDTSCP[bit 27] = 0.

Virtual-8086 Mode Exceptions

#GP(0)

  • If the TSD flag in register CR4 is set.

#UD

  • If the LOCK prefix is used.

  • If CPUID.80000001H:EDX.RDTSCP[bit 27] = 0.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

Same exceptions as in protected mode.

첫 댓글을 달아주세요!
프로필 사진 없음
강좌에 관련 없이 궁금한 내용은 여기를 사용해주세요

    댓글을 불러오는 중입니다..